How to Set up a Tub: Install an Acrylic Bathtub as Well as Tub Surround

How to Set up a Tub: Install an Acrylic Bathtub as Well as Tub Surround

Blog Article

Book Your Service

Were you interested in details about Installing A Bathtub?

Setting up a bathtub isn't specifically rocket science, yet it does need strong plumbing, carpentry, and also often, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately tough project. If the old bathtub is readily easily accessible, the project can relocate quickly; if you have to open up a wall to get rid of the old tub as well as position the new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly need a helper to vacate the old tub as well as set in the new one. See to it you have certified on your own for the job as well as fit attempting it. Instead of working with a professional to take over a halfway-completed task, it is better to think about using one before you begin. Opportunities are you might need an expert plumber to make tube links.
This write-up will assist you mount a new bathtub in your shower room if you have actually already purchased a brand-new bathtub and also don't need to alter the setup of your previous water supply pipes.
Your tools and also product checklist ought to make up the following:

New Tub

Hammer

Pipe Wrenches

Prybar

Shatterproof glass

Degree

Pliers

Flexible Wrench

Putty Knife

Screwdriver

Cold Blade

Measuring tape

Pipe Caps

Getting ready for the Installment

Firstly, the supporting framework provided with the bathroom should be fitted (if needed) according to the maker's instructions. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps system to avoid stress on the bath tub.
Fit the adaptable tap ports to the bottom of both faucets making use of 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize all of the supplied washers.
Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last setting.

Removing Old Taps

If you need to replace old taps with new ones as a part of your installment, after that the first thing you need to do is separate the water system. After doing so, switch on the taps to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be quite troublesome due to the restricted accessibility that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a towel all set for the staying water that will come from the pipelines. When the supply pipes have been gotten rid of, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming throughout this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Prior to carrying on to fit the new faucets, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.

Mounting the Bathtub

Making use of both wooden boards under its feet, position the tub in the called for setting. The wooden boards are handy in uniformly spreading the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 little factors.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by inspecting the level as well as readjusting the feet on the tub till the spirit level reviews level.
To mount taps, fit all-time low of the furthest adaptable faucet port to the ideal supply pipe by making a compression sign up with; then do the very same for the other tap.
Activate the supply of water and also inspect all joints and also new pipework for leakages and tighten them if needed. Load the tub as well as also inspect the overflow electrical outlet as well as the regular outlet for leaks.
Ultimately, repair the bath paneling as defined in the manufacturer's user's manual. Tiling and also sealing around the tub needs to wait until the tub has actually been used a minimum of when as this will settle it right into its last position.

Suitable New Touches

If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the placing opening in the bath/basin making certain that the washers are in area in between the tap as well as the sink. Safeguard the tap in place with the maker provided backnut. Once the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet connectors. The former type must be attached to the tap ends first, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.

Tiling Around the Bathtub

In the area where the bath satisfies the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to split an inflexible seal, creating the water to penetrate the wall between the bath as well as the tiling, causing difficulties with wetness and also possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and also installations. They are marketed in tubes and also cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched newspaper or soft rope. Remember to always load the bath tub with water prior to sealing, to allow for the activity experienced when the bathtub remains in use. The sealant can fracture rather very early if you do not think about this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof glue and also cement.

A Step-by-Step Guide to Installing a Bathtub

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

Remove the Existing Bathtub

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

Choose the Right Bathtub

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

Install the Plumbing and Ledger Board

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

Install the Bathtub

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

Hook up the Plumbing

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

Install the Bathtub Surround

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

I found that piece of writing about Installing A Bathtub when surfing around the internet. Sharing is caring. Who knows, you may very well be doing someone a favor. Thank-you for going through it.

Click

Report this page